top of page

| Whole Home Rewiring in Orange County, CA

Wilson Electric rewires homes from Huntington Beach to Dana Point, replacing outdated, undersized, or unsafe wiring with a modern copper electrical system built for how your family lives today. We're a Costa Mesa–based electrical contractor focused on custom residential work. We're licensed, insured, and bonded, and every rewire is permitted and inspected.

​

CA C-10 License #1108912 | Certified Journeyman Electrician | Insured & Bonded | SPAN Certified | Tesla Certified | Lutron Certified

| What Is Whole Home Rewiring?

Whole home rewiring replaces the branch-circuit wiring that carries power from your electrical panel to every outlet, switch, light, and appliance in your house. The old wiring is removed or safely abandoned, and new copper circuits, electrical boxes, grounding, and devices are installed to meet the current California Electrical Code.

​

A rewire is different from a repair. Repairs fix one problem in one place. A rewire resets the whole system, so you're not chasing the next failure in 70-year-old wiring hidden inside your walls.

| Signs Your Home Needs Rewiring

Older wiring rarely fails all at once. It shows warning signs first. Call a licensed electrician if you notice any of these:

​

| Breakers that trip often, or fuses that blow

​

| Lights that flicker or dim when the A/C, microwave, or a hair dryer turns on

​

| Outlets or switch plates that feel warm, buzz, spark, or show scorch marks

​

| A burning or "hot plastic" smell with no obvious source

​

| Two-prong, ungrounded outlets throughout the house

​

| Outlets that are loose, cracked, or won't hold a plug

​

| Too few outlets, and extension cords and power strips everywhere

​

| Knob-and-tube, cloth-insulated, or aluminum branch-circuit wiring

​

| A home inspector or insurance company flagging the electrical system

​

| Original wiring in a home that's 50 years old or more

​

Some of these, especially heat, sparking, and burning smells, can indicate a fire hazard. If you notice them, turn off the affected circuit and have it inspected right away.

| Types of Outdated Wiring We Replace in Orange County Homes

Much of Orange County's housing was built between the 1950s and the 1970s, and the type of wiring in your home says a lot about how it was built and what it needs.

​

​

| Knob-and-Tube Wiring

​

Found in the oldest homes, knob-and-tube uses individual wires on porcelain knobs and tubes with no ground conductor. Its insulation becomes brittle with age, it was never meant to be covered by attic insulation, and many insurance companies won't cover homes where it's still active.

​

​

​

| Cloth-Insulated and Early Ungrounded Wiring

 

Many mid-century homes were wired with cloth-sheathed or early plastic-sheathed cable that has no ground wire. Over decades the insulation can crack and crumble, especially in hot attics. These homes typically have two-prong outlets throughout.

​

​

 

| Aluminum Branch-Circuit Wiring

 

Some homes built from the mid-1960s to the early 1970s used aluminum wire for branch circuits. Aluminum expands and contracts more than copper and can loosen and overheat at outlets, switches, and splices. It can be remediated with approved connectors or fully replaced with copper.

​

​

 

| Undersized and Overloaded Circuits

 

Even newer wiring can be outmatched. Homes built before EV chargers, heat pumps, induction cooking, and home offices often have too few circuits and too little capacity, which leads to overloads, nuisance tripping, and a lot of extension cords.

| Full Rewire vs. Partial Rewire

Not every home needs to be rewired from top to bottom. After evaluating your system, we'll recommend the approach that makes sense for your home and budget:

​

​

| Full rewire: Every branch circuit is replaced. This is best for knob-and-tube, deteriorated cloth wiring, or homes with widespread problems.

​

| Partial rewire: Specific areas or circuits are replaced, such as a kitchen, an addition, or the circuits that failed inspection. This often makes sense during a remodel.

​

| Targeted upgrades: Grounding, aluminum wiring remediation, new dedicated circuits, or device replacement when the core wiring is still sound.

​

​

You'll always get a straight answer from Wilson Electric. If your wiring doesn't need replacing, we'll tell you.

| What's Included in a Wilson Electric Rewire

| New copper branch-circuit wiring sized for modern loads

​

| New electrical boxes, outlets, and switches, including tamper-resistant receptacles

​

| Proper equipment grounding throughout the home

​

| AFCI and GFCI protection where the California Electrical Code requires it

 

| Dedicated circuits for kitchens, laundry, bathrooms, HVAC, and major appliances

​

| Panel evaluation, with a main panel upgrade when needed

​

| Removal or safe abandonment of old wiring

​

| Electrical permit, rough-in inspection, and final inspection

​

| Coordination of drywall and stucco patching

 

| A clearly labeled panel and your permit documentation

| Built to the 2025 California Electrical Code

Permitted electrical work in California must meet the current California Electrical Code. The 2025 edition, which is based on the 2023 National Electrical Code, took effect statewide on January 1, 2026, and each Orange County city enforces it through its building department.

​

For homeowners, that means your rewire includes modern safety protections that older homes don't have. AFCI breakers help prevent fires caused by arcing wires. GFCI protection guards against shock in kitchens, bathrooms, laundry areas, garages, and outdoors. Tamper-resistant outlets protect children, and proper grounding protects your electronics. Depending on the scope of your project, your city may also require updated smoke and carbon monoxide alarms. We'll tell you up front if that applies.

| Rewiring Challenges Unique to Coastal Orange County

Rewiring a beach-area home isn't the same as rewiring a house inland. After more than a decade working along the coast, we plan around these from day one:

​

​

| Salt Air and Corrosion

 

Homes near the ocean are exposed to salt-laden air that accelerates corrosion on exterior connections, service equipment, and outdoor outlets. We use materials and weatherproof fittings suited to coastal conditions.

​

​

​

| Stucco Exteriors and Plaster Walls

 

Many older OC homes have stucco exteriors and plaster interiors that are harder to open and patch than standard drywall. We plan wire routes to limit openings, and we coordinate experienced patching so repairs blend in.

​

​

 

| Slab Foundations and Tight Attics

 

Most Southern California homes sit on concrete slabs with no crawlspace beneath, which means most wiring has to be routed from the attic. Low-slope roofs and tight attic spaces take careful planning, and that experience is often what separates a clean rewire from a messy one.

 

 

| HOAs and Close Neighbors

 

In many communities from Huntington Beach to Dana Point, HOA rules, tight lot lines, and parking limits affect how work gets scheduled and staged. We keep the job organized and respectful of your neighbors.

​

​

| Rewiring and Panel Upgrades

Your new wiring is only as good as the electrical panel feeding it. Many older Orange County homes still have 60- or 100-amp service, or panels from brands that are no longer recommended. When we rewire, we evaluate your panel and electrical service. If an upgrade is needed, we handle it as part of the same project, which is usually faster and more cost-effective than doing the two separately.

​

| As a SPAN-certified installer, we can also install a SPAN smart panel. It lets you monitor and control individual circuits from your phone and manage loads for EV charging and battery backup.

​

Learn more about our electrical panel upgrades

| Future-Ready Wiring for Modern Homes

A rewire is the best opportunity you'll have to set your home up for the next 30+ years. While walls are open, we can plan capacity and pre-wire for:

​

| EV charging (we're Tesla certified)

​

| Solar and home battery storage

​

| Heat pump HVAC and heat pump water heaters

​

| Induction ranges and all-electric kitchens

 

| Lutron lighting control and smart home systems (we're Lutron certified)

 

| Dedicated home office and network circuits

​

| Exterior, landscape, and security lighting

| Our Whole Home Rewiring Process

1. On-site evaluation. We inspect your panel, service, wiring type, attic and crawlspace access, and existing loads, and talk through how you use your home and what you plan to add.

​

2. Detailed written estimate. You receive a clear, itemized proposal covering scope, circuits, devices, panel work, patching, schedule, and exclusions.

​

3. Permits and planning. We pull the electrical permit with your city and build a work plan that keeps your household running during the project.

 

4. Protection and prep. We protect floors, furniture, and finishes and set up a clean, organized work area.

​

5. Rough-in. We remove or abandon the old wiring and run new copper circuits, boxes, and grounding through walls, ceilings, and the attic using targeted access points.

​

6. Rough-in inspection. The city inspector reviews our rough-in work before any walls are closed.

 

7. Finish and patching. We install new outlets, switches, fixtures, and protective devices, then coordinate drywall and stucco patching.

 

8. Final inspection and walkthrough. After final sign-off, we walk you through your new system, test every circuit, and leave you with a clearly labeled panel and your permit documentation.

| How Much Does It Cost to Rewire a House in Orange County?

Every home is different, so we price rewires from an on-site evaluation, or stamped blueprints from your architect. The biggest cost factors are:

​

​

| Square footage and number of stories

​

| Attic and crawlspace access, and how easily wire can be routed

​

| Wall and ceiling finishes (drywall, plaster, stucco, or finished ceilings)

 

| The number of circuits, outlets, switches, and fixtures

​

| Whether the panel or electrical service needs an upgrade

​

| Added features like EV charger circuits, lighting control, or pre-wiring for solar

​

| Whether the rewire is happening during a remodel, when walls are already open

​

​

Most Orange County rewires we complete fall between $17 to $22 per square foot, depending on the scope. 

| How Long Does a Rewire Take?

Most single-family homes take about one to two weeks of electrical work, plus time for inspections and patching. Larger custom homes and rewires combined with a remodel take longer. We make sure to work closely with other trades and their schedules, so a job is never held up or trailing behind deadlines.

| Rewiring, Insurance, and Selling Your Home

Outdated wiring is one of the most common items flagged in home inspections, and it can complicate insurance and sales. Knob-and-tube in particular can make it hard to get or keep a homeowners policy. A permitted rewire, with inspection sign-off and documentation, removes that red flag for buyers, lenders, and insurers.

| Why Orange County Homeowners Choose Wilson Electric

| Custom home specialists: More than 10 years of electrical experience in custom residential homes along the Orange County coast.

​

| Owner-led work: Taylor Wilson, a Certified Journeyman Electrician, manages every project with a small, dedicated crew.

​

| Licensed and accountable: California C-10 License #1108912, insured and bonded.

​

| Modern-system expertise: SPAN, Tesla, and Lutron certifications mean your new wiring is ready for smart panels, EV charging, and lighting control.

​

| Clear, itemized estimates: You know what you're paying for before work starts.

 

| Permits handled: We pull permits, schedule inspections, and meet the inspector.

​

| Respect for your home: Protected floors, minimal wall openings, clean job sites, and coordinated patching.

| Whole Home Rewiring Service Areas

Wilson Electric provides whole home rewiring throughout Orange County, with a focus on the coastal communities from Huntington Beach to Dana Point.

​

​

​

| Whole Home Rewiring in Costa Mesa

​

Costa Mesa is our home base. Many of the city's neighborhoods were built in the post-war and mid-century building boom, and plenty of those homes still run on original wiring and small panels that can't keep up with modern loads. We rewire Costa Mesa homes for safety, remodels, and additions, often with a panel upgrade at the same time.

​

Learn more about re-wiring in Costa Mesa

​

​

​

| Whole Home Rewiring in Newport Beach and Corona del Mar

​

From older beach cottages on the peninsula to custom homes in Corona del Mar and the hillside neighborhoods, Newport Beach homes range widely in age and complexity. We specialize in rewires for high-end remodels, including Lutron lighting control and smart panel integration, as well as coastal-grade work for homes exposed to salt air.

​

Learn more about re-wiring in Newport Beach

​

​

​

| Whole Home Rewiring in Huntington Beach

​

Huntington Beach has a large stock of tract homes from the 1960s and '70s, along with older homes closer to downtown. Coastal air is tough on aging connections, and many of these homes are due for new wiring, grounding, and more capacity for EV chargers and heat pumps. We rewire homes across Huntington Beach, from full rewires to remodel and addition work.

​

Learn more about re-wiring in Huntington Beach

​

​

​

| Whole Home Rewiring in Irvine

​

Many Irvine homes are newer, but some of the city's earliest neighborhoods date to the era when aluminum branch wiring and smaller electrical services were common. We inspect, remediate, or replace aluminum wiring and upgrade circuits for today's all-electric homes.

​

Learn more about re-wiring in Irvine

​

​

​

| Whole Home Rewiring in Laguna Beach

​

Laguna Beach's older cottages and hillside and canyon homes often have original wiring, tight access, and unique construction. We plan rewires carefully to protect each home's character while bringing the electrical system up to current code.

​

Learn more about re-wiring in Laguna Beach

​

​

​

| Whole Home Rewiring in Dana Point

​

At the southern end of our coastal service area, Dana Point homes face the same salt-air exposure as the rest of the coast. We rewire coastal homes and remodels with materials and methods built to last near the ocean.

​

Learn more about re-wiring in Dana Point

​

​

​

Also Serving:

​

| Fountain Valley

| Seal Beach

| Westminster

| Santa Ana

| Tustin

| Laguna Niguel

| Laguna Hills

| Aliso Viejo

| Mission Viejo

| Lake Forest

| San Juan Capistrano

​

| Whole Home Rewiring FAQs

| How much does it cost to rewire a house in Orange County?

​

Rewiring cost depends on the home's square footage, number of stories, attic and crawlspace access, wall finishes like plaster or stucco, the number of circuits and devices, and whether the electrical panel also needs an upgrade. Because two homes of the same size can differ a lot in access and scope, Wilson Electric provides a detailed, itemized written estimate after an on-site evaluation.

​

| How long does it take to rewire a whole house?

​

Most single-family homes take about one to two weeks of electrical work, plus time for city inspections and wall patching. Larger custom homes, multi-story homes, and rewires combined with a remodel can take longer. You get a project schedule with your estimate.

​

| Can I live in my house while it is being rewired?

​

In most cases, yes. We rewire room by room and restore power at the end of each workday whenever possible, so you can keep living in your home. If your rewire is part of a larger remodel, we coordinate with your general contractor's schedule.

​

| Will rewiring damage my walls and ceilings?

​

We route new wiring through the attic, crawlspace, and existing chases wherever possible and make small, targeted openings only where needed. Wall and stucco patching is coordinated as part of the project so your home is left finished, not full of holes.

​

| Do I need a permit to rewire my house in California?

​

Yes. A whole home rewire requires an electrical permit and city inspections in every Orange County city we serve. Wilson Electric pulls the permit, schedules the rough-in and final inspections, and meets the inspector on site.

​

| What electrical code does a rewire need to meet?

​

Permitted work in California must meet the current California Electrical Code. The 2025 California Electrical Code, based on the 2023 National Electrical Code, took effect January 1, 2026. Your city building department enforces it, along with any local amendments.

​

| Do I need a new electrical panel when I rewire?

​

Not always, but many older homes have panels that are undersized, worn out, or a brand that is no longer recommended. We evaluate your panel and service during the estimate and, if needed, complete a main panel upgrade at the same time, which is usually more efficient than doing the two projects separately.

​

| Is knob-and-tube wiring dangerous?

​

Knob-and-tube wiring has no ground conductor, its insulation becomes brittle with age, and it was never designed to be buried in attic insulation or to carry modern loads. Many insurance companies will not write or renew policies on homes with active knob-and-tube wiring, which is a common reason homeowners choose to rewire.

​

| Is aluminum wiring safe?

​

Aluminum branch-circuit wiring, used in some homes built from the mid-1960s to the early 1970s, expands and contracts more than copper and can loosen and overheat at outlets, switches, and splices. It can be remediated with approved connectors at each connection or replaced with copper. We inspect your system and explain both options.

​

| Do two-prong outlets mean my house needs rewiring?

​

Two-prong outlets usually mean the circuits have no ground wire. That doesn't always require a full rewire, but it does limit surge protection and safe use of three-prong appliances and electronics. We can test your circuits and recommend either targeted upgrades or a rewire.

​

| Does rewiring increase home value or help with insurance?

​

A permitted rewire with up-to-date wiring and a modern panel removes a red flag that home inspectors, buyers, and insurers look for. Insurance treatment varies by carrier, so we recommend asking your insurer how a rewire affects your policy. We provide permit and inspection documentation for your records.

​

| Should I rewire before a remodel or EV charger installation?

​

If your home has outdated wiring, a remodel is the best time to rewire because walls and ceilings are already open. It is also the right time to plan capacity for an EV charger, heat pump, induction range, or solar and battery system so you are not opening walls again later.

Schedule An On-Site or Virtual Rewiring Estimate

bottom of page