top of page

| Electrical Subpanel Installation in Orange County, CA

A subpanel is a second breaker panel fed from your main panel. It puts circuits where you actually need them: in the garage, in an ADU, out at a backyard studio or next to the pool equipment. It is one of the most common electrical jobs in Orange County, and also one of the most often done wrong. Wilson Electric plans every subpanel from a load calculation, builds it for coastal conditions, and permits it through your city.

 

We are a licensed C-10 electrical contractor (#1108912) based in Costa Mesa, insured and bonded, and certified by SPAN, Tesla and Lutron.

| Subpanel Installation: Quick Answers

| Who: Wilson Electric, a licensed California C-10 electrical contractor (#1108912) based in Costa Mesa, CA.


| Where: Coastal and South Orange County, from Seal Beach to San Clemente.


| What: Subpanels for garages, ADUs, detached studios, pools and spas, additions, custom-home wings, EV charging and battery backup.


| Key fact: A subpanel adds breaker space, not capacity. Your main service still sets the limit.


| Code: Designed to the 2025 California Electrical Code, which took effect statewide on January 1, 2026.


| Permits: Every subpanel is permitted and inspected through your city.


| Timeline: Usually one to two days of electrical work for an attached location, longer for trenching.


| Cost: Itemized written estimate after we see your main panel and the feeder route.

| A Subpanel Adds Space, Not Power

Many electricians sell a subpanel as a way to "add capacity." It does not. If your main service is 100 amps, a 100-amp subpanel does not give you 200. Every amp the subpanel delivers is still drawn through the main service and the utility's meter.

​

What a subpanel does do is just as useful when it is the right answer:

​


| Adds breaker spaces when your main panel is full


| Puts a disconnect and breakers in the building you are working in, so you are not walking to the house to reset a breaker


| Shortens long circuit runs, which reduces voltage drop for tools, chargers and pumps


| Organizes a remodel, addition or custom-home wing into its own panel


| Sets aside chosen circuits for battery backup

​

​

Before we recommend a subpanel, we do a load calculation on your house. If it shows your service has room, a subpanel is often the lowest-cost fix. If it shows you are already near the limit, we will tell you that, and walk you through a main panel upgrade, a SPAN smart panel, or EV load management instead. A subpanel on an overloaded service just moves the problem to a new box.

| Subpanel, Panel Upgrade or Smart Panel?

| Main panel is full, service has room | Subpanel | Adds spaces without replacing the service.


| Adding a garage, studio or ADU | Subpanel (or a separate meter for some ADUs) | Gives the building its own disconnect and breakers.


| Load calculation shows the service is maxed out | Main panel upgrade | Only a bigger service adds real capacity.


| Adding an EV charger, heat pump or induction range on a tight service | SPAN smart panel or load management | Shares capacity between big loads, so an upgrade may not be needed.


| Adding battery backup for part of the house | Backup loads subpanel | Keeps the circuits you choose powered during an outage.


| Old panel with known reliability problems | Replace the main panel first | Do not extend an unsafe panel.

| Where Orange County Homes Need Subpanels

| Garage and Workshop Subpanels

​

EV chargers, table saws, compressors, freezers, gym equipment and garage refrigerators add up quickly. A garage subpanel gives them dedicated circuits and leaves spaces for the next charger. Coastal OC garages are also where many homes keep their laundry and water heater, so we plan around those too.

 

 

 

| ADU and Junior ADU Panels

 

California has made ADUs easier to permit, and Orange County homeowners have built them in large numbers. An all-electric ADU with a heat pump, induction cooking and a heat-pump water heater needs a properly sized panel. Under the 2025 California Electrical Code, a feeder-supplied dwelling unit generally needs an outdoor emergency disconnect for first responders. We plan that from the start so it does not hold up your final inspection.

 

 

 

| Detached Studios, Offices and Pool Houses

 

Detached buildings need their own grounding electrode, a four-wire feeder and a disconnect at the building. We route feeders through conduit or trench them, and we size them for distance so the lights do not dim when the heater turns on.

 

 

 

| Pool, Spa and Outdoor Kitchen Panels

 

Pool pumps, heaters, spa blowers, landscape lighting and outdoor kitchen appliances are often grouped in a subpanel near the equipment pad. These are wet, salty locations, so the enclosure and fittings matter as much as the breakers.

 

 

 

| Custom Homes, Additions and Remodels

 

Large custom homes often have several subpanels, one for each wing or floor, and one for a Lutron lighting control system. This is the type of work we do most. On remodels and additions, a new subpanel keeps the new work organized and keeps you from overloading an old main panel.

​

​

​

| Battery Backup Loads Panels

 

Many partial-home backup systems use a dedicated backup loads subpanel that holds the circuits you want to keep running during an outage. As Tesla-certified installers, we help you choose those circuits, so the battery powers what matters instead of running down on loads you do not need.

| What We Check Before We Quote

A fair price depends on understanding the job first. At the estimate, we look at:

 


| Your main service size, panel bus rating, panel condition and open breaker spaces


| A load calculation of what you have now and what you plan to add


| The feeder route: attic, crawlspace, garage ceiling, finished wall, exterior conduit or trench


| Feeder distance and voltage drop, and whether copper or aluminum feeder is the better value


| The panel location, including working clearance and the rule that panels cannot go in clothes closets or bathrooms


| Grounding and bonding: isolated neutrals in the subpanel, and a grounding electrode at detached buildings


| Salt-air exposure and whether the enclosure needs to be stainless or corrosion-resistant


| HOA rules, utility requirements and city permit requirements

| Subpanel Mistakes We Find and Fix

When we open subpanels that someone else installed, these are the problems we see most:

 

​

| Neutral and ground bonded in the subpanel

 

This puts normal current on ground wires and metal pipes. Neutral and ground should only be bonded at the main service.

 

 

 

| Three-wire feeders to detached garages

​

Older installs often lack a separate ground wire. New work needs four wires and a grounding electrode at the building.

​

​

​

| Large breakers on small wire

​

A 100-amp breaker feeding wire rated for 60 amps will not protect that wire. We match the feeder to the breaker.

​

​

​

| Panels in closets or behind shelves

​

Panels need clear working space and cannot go in clothes closets. We relocate panels that cannot be safely reached.

​

​

​

| Indoor panels mounted outside

​

An indoor-rated box on an exterior wall near the ocean can rust through and let water in. Outdoor panels need an outdoor-rated enclosure.

​

​

​

| Unpermitted subpanels

​

These often show up during home inspections when you sell. We can evaluate them, correct them and permit them.

| Built for the Coast

From Seal Beach to San Clemente, salt air is hard on electrical equipment. Steel enclosures rust, screws seize, and aluminum lugs corrode if they are not treated. On coastal homes, we use outdoor-rated enclosures, stainless or coated hardware where there is direct spray, sealed conduit entries, and anti-oxidant compound on aluminum terminations. Wherever the layout allows, we mount panels on the side of the house away from the wind off the ocean.

| Our Subpanel Installation Process

1. Walk the house and the route: We look at your main panel, the bus rating, the open spaces and the path a feeder would take, and we ask what you plan to add over the next five to ten years.


2. Run the load calculation: We calculate your existing and planned loads under Article 220 of the California Electrical Code to confirm your service can support the new feeder.


3. Give you an itemized proposal: You get a written estimate that shows the subpanel size, feeder size and material, the route, permit costs and any patching, so you can compare it line by line.


4. Pull the permit: We file with your city's building department and plan around HOA rules and access.


5. Install the feeder and panel: We set the panel with code clearances, run the feeder, isolate neutrals from grounds and install grounding electrodes at detached buildings.


6. Move or add circuits: We land new circuits or move existing ones into the subpanel and label every breaker in plain language.


7. Pass inspection: We meet the city inspector, then test every circuit under load.


8. Hand over documentation: You get a labeled directory, the finaled permit and photos of what is inside the walls, which helps when you sell or remodel later.

| What Affects Subpanel Cost

| Subpanel size and the number of circuits added or moved


| Feeder length and wire size; longer runs need larger wire to limit voltage drop


| The route: open attic and garage runs cost less than finished walls or trenching


| Detached buildings, which need a grounding electrode and often an outdoor disconnect


| Corrosion-resistant enclosures for salt-air locations


| Permit fees, which vary by city


| Whether the main panel needs repairs or replacement first

​

Most Subpanels we install fall between $1,500 to $3,500, dependent on location, distance from Main Panel, and amperage rating.

| Subpanel Installation Across Orange County

We install subpanels from our base in Costa Mesa throughout coastal and South Orange County. Choose your city for local details:

​


| Subpanel Installation in Costa Mesa
| Subpanel Installation in Newport Beach
| Subpanel Installation in Huntington Beach
| Subpanel Installation in Irvine
| Subpanel Installation in Laguna Beach
| Subpanel Installation in Dana Point
| Subpanel Installation in Fountain Valley
| Subpanel Installation in Seal Beach
| Subpanel Installation in Westminster
| Subpanel Installation in Santa Ana
| Subpanel Installation in Tustin
| Subpanel Installation in Laguna Niguel
| Subpanel Installation in Laguna Hills
| Subpanel Installation in Aliso Viejo
| Subpanel Installation in Mission Viejo
| Subpanel Installation in Lake Forest
| Subpanel Installation in San Juan Capistrano

​

​

Corona del Mar is covered on our Newport Beach page.

| Electrical Subpanel FAQs

| Does a subpanel increase my home's electrical capacity?


No. A subpanel adds breaker spaces and puts circuits closer to where they are used, but every amp it delivers still comes through your main service. If a load calculation shows your service is already near its limit, you need a service upgrade or load management, not just a subpanel.

​

| How much does it cost to install a subpanel in Orange County?


Most of the price is set by three things: the feeder distance and route, the subpanel size, and whether the run is through an attic, through a finished wall or in a trench. We give you an itemized written estimate after looking at your main panel and the route.

​

| What size subpanel do I need?


We size it from a load calculation, not a guess. A garage with an EV charger and a few tool circuits is often 60 to 100 amps, while an ADU with electric cooking, a heat pump and a water heater is often 100 amps or more. Your main service has to be able to support the feeder.

​

| Do I need a permit to install a subpanel?


Yes. Every Orange County city we serve requires an electrical permit and inspection for a new subpanel. We pull the permit, schedule the inspections and meet the inspector.

​

| Does an ADU need its own electrical panel?


An ADU almost always gets its own panel, either a subpanel fed from the main house or a separate service with its own meter. Under the 2025 California Electrical Code, a dwelling unit fed by a feeder generally also needs an outdoor emergency disconnect. We help you decide between a subpanel and a separate meter based on your service size and budget.

​

| Can a subpanel go in a closet or bathroom?


No. Code does not allow panelboards in clothes closets or bathrooms, and every panel needs a clear working space in front of it, typically 30 inches wide and 36 inches deep with 6.5 feet of headroom. We plan the location before anything is mounted.

​

| Why are the neutral and ground separated in a subpanel?


Neutral and ground are bonded together only at the main service disconnect. In a subpanel they sit on separate, isolated bars so normal current never flows on the ground wires or on metal parts of the house. A bonded subpanel is one of the most common mistakes we find.

​

| Does a detached garage or studio need a ground rod?


Usually, yes. A detached building fed by a feeder needs its own grounding electrode system plus an equipment grounding conductor run with the feeder. Older three-wire feeders to detached buildings are not allowed on new work.

​

| Can I add a subpanel for an EV charger?


Yes, a garage subpanel is a common way to add a charger and leave room for future circuits. If your service is tight, an EV energy management system or a SPAN smart panel can let you add charging without a full service upgrade.

​

| Can a subpanel be used for battery backup?


Yes. Partial-home backup systems often move selected circuits like the refrigerator, lights, internet and well or sump pumps into a dedicated backup loads panel. As Tesla-certified installers, we lay out that panel so the circuits you care about stay on during an outage.

​

| How long does a subpanel installation take?


Most indoor or attached-garage subpanels take one to two days of electrical work. Detached buildings with trenching take longer. Inspections are scheduled with the city on top of that.

​

| What kind of subpanel enclosure is best near the ocean?


Outdoor panels need a rainproof NEMA 3R enclosure at a minimum. On homes with direct salt spray, we often use stainless or corrosion-resistant enclosures and sealed fittings, because standard painted steel can rust through within a few years on the coast.

Schedule An On-Site or Virtual Estimate

bottom of page